Showing results: 226 - 240 of 336 items found.
-
ERAVANT
Probe antennas are offered as both standard and custom models with a rectangular waveguide interface. Probe antennas can only support linear polarization. These antennas are often used to measure the gain of other antennas by comparing the signal levels of the probe antenna and antenna under testing. The standard models operate across the full waveguide band and offer 6.5 dB nominal gain and 115 and 60 degrees half power beamwidth at center frequency. The below standard offering covers the frequency range of 8.2 to 170 GHz.
-
IQtouch -
Johnstech International Corporation
The new IQtouch™ Micro Final Test Probe Arrays, for example, deliver unsurpassed low and stable contact resistance (CRES). This is accomplished through a balanced optimization among several critical and competing engineered parameters, including effective test signal transmission path, probe / wafer interface (“touch”) points and elastomeric web forces, and precision manufactured components for superior X/Y/Z co-planarity
-
AP033 -
Teledyne LeCroy
Fully Integrated: With the ProBus™ interface, the AP033 becomes an integral part of the oscilloscope. The probe sensitivity and offset can be controlled from the oscilloscope front panel, the probe front panel, or by using remote control commands (GPIB or RS-232). Sensitivity, offset, input capacitance, and common mode voltage range are displayed on the oscilloscope screen. When used with a LeCroy digital oscilloscope, no external power supply is required.
-
DP750-100 -
Shenzhen Micsig Instruments Co., Ltd.
*The leads and probe are with shielded design, interface ends are integrated in a compact box, no need to twist the cables, leads to a lower noise floor and has less interference. *Support one-press Zero calibration and automatic overrange alarm.*Directly powered by Micsig UPI interface, realise auto scaling setup, can also powered by oscilloscope via USB cable.
-
Guided Wave
The sample interface is a virtual “windows into the process” and is a critical component of any optical analyzer system. Guided Wave sample interfaces (probes, flow cells) are designed for use with NIR or UV/Vis fiber optic coupled analyzers. They are designed to be rugged and reliable in harsh chemical and physical process conditions while providing optimal transmission for long-term reliable measurements.
-
CA10 -
Teledyne LeCroy
The CA10 is a programmable and customizable interface device that seamlessly incorporates third party current transducers/transformers with Teledyne LeCroy oscilloscopes or motor drive analyzers. It allows the third party device to be recognized and operate as if it were a Teledyne LeCroy probe.
-
SemiProbe
The SemiProbe PILOT Control Software Suite semiautomatic and fully automatic probe systems employs the SemiProbe patented Adaptive Architecture. Software modules can be added to the base system as needed. PILOT Control Software consists of a Microsoft Windows-based user interface built on the SemiServer application for communicating to and from the probe system. Individual customer applications can be integrated with PILOT Control Software for a customized system to meet individual needs.
-
The Chameleon -
Circuit Check, Inc.
The Circuit Check kit called the Chameleon allows easy re-use of a majority of an ICT fixture’s major components. The Chameleon includes a full size probe plate and interface alignment plate so all valuable tester resources are available. The probe plate assembly is held in place with twelve (12) screws and the vacuum box’s interchangeable push plate is easily replaced by removing four (4) shoulder screws.
-
Utel Systems
Utel Capture is a complete telecoms network monitoring platform based on virtual (or physical probes for legacy interfaces) that enables data acquisition from control and user planes. It captures real-time data to provide valuable insights into network performance.
-
Acute LA3068B+ -
TEAM SOLUTIONS, INC.
*LA3000E+/B+ series logic analyzer*PC-based*68 / 136 channels*USB 3.0 interface, 12V power adaptor*4GHz Timing Analysis / 250MHz State Analysis*32Gb RAM*Active Probes*Logic, State, Protocol triggers
-
TransData, Inc.
Abacus Electrics ANSI Type 2 optical probes utilize infra-red LED technology to provide a galvanically isolated, bi-directional communications interface between energy meters and laptop computers or handheld devices for onsite data retrieval, programming and diagnostics.
-
ZD200 -
Teledyne LeCroy
With the ProBus interface, the ZD200 becomes an integral part of the oscilloscope. The probe sensitivity and offset are automatically optimized based on the oscilloscope gain settings, so control is transparent to the user. When used with a LeCroy digital oscilloscope, no external power supply is required.
-
MAJIC -
Mentor Graphics Corp.
MAJIC (Multi-Architecture JTAG Interface Controllers) JTAG Probes are small, stand-alone, processor-based systems that provide an intelligent connection between host-based development tools (the debugger) and an embedded processor via its standardized JTAG debug logic IP macrocell.
-
Green Hills Probe V4 -
Green Hill Software, Inc.
The Green Hills Probe is an advanced hardware debug device that connects to the onboard debug ports present on most modern microprocessors, such as IEEE 1149.1 JTAG and BDM. With support for more than one thousand devices from over thirty manufacturers, a flexible electrical interface, and out-of-the-box support for the largest multicore systems, the Green Hills Probe provides fast, reliable debugging, programming, and system visibility to projects present and future.
-
DH-QL -
Teledyne LeCroy
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.